Guidelines to Paint a Garage Door Properly 

When your garage door starts to look worn out, do not start to look at replacements just yet. In fact, you can opt to provide your garage with a totally fresh look with a new coat of paint. Before breaking out the rollers and paint cans, it is essential to know that exterior painting is definitely not similar to painting your home’s walls. Below are the guidelines you need to consider to properly paint your garage door. 

Inspect the weather 

Apparently, your outdoor painting project will be most likely dependent on the weather compared to repainting your room indoors. Hence, make sure to inspect the weather and attempt to only paint any painting projects you have in your home on a clear and cool day. The perfect conditions would be if the temperature remains between 50-75 F° with indirect sunlight, low wind, and low humidity. As much as possible, attempt to search for 3 days in a row that have these conditions on weather forecasts you can see on the internet or news.  

Get the materials 

You will need a gallon of both the primer and the paint for a garage door that can fit 2 vehicles. Bit, when you plan to cover dark colors with lighter ones, you probably need to get a little more. Also, here are the other materials that you need: 

  • All-purpose cleaner 
  • Clean rags 
  • Drop cloth 
  • Fine sandpaper 
  • Hose 
  • Nylon paintbrush (preferably 2 inches) 
  • Paint roller (preferably ¾ inch) 
  • Painter’s tape 
  • Sponge 
  • Ladder or step stool 
  • Wire brush 

Prepare the door 

You cannot begin to paint a garage door immediately. It is expected to have tons of rust, grit, grime, and dirt compared to your inside walls. Hence, it will require tons of prep work. Scrub off any chipped or rusted areas using your wire brush. Then, using sandpaper, sand those affected spots to make a smooth base.  

After doing this, clean the whole room with a sponge and an all-purpose cleaner. Use your garden hose to rinse it and then allow the surface to dry with clean rags or towels. Allow the door to finish air-drying for approximately 1 hour.  

Cover and tape 

As your door dries, try to cover up anything you do not want to be pained on, which includes taping any hardware and trim that you don’t plan to paint. Also, you can put down a drop cloth to avoid staining your concrete. Apart from that, you may need to think about disengaging your lift motor for you to lower and raise your garage door as required as you work.  

Prime 

Begin by priming your garage door’s inset panel using your paint roller or paintbrush. As you paint the trim, make sure to save this for last. Allow it to dry for about twelve hours.  

Paint 

This is the time when you have to apply the paint color of your choice. Make sure to start your way from the top to the bottom. If you don’t know how to properly do this, ask for the help from the expert painters Carson City NV today.          

 

When Should You Consider Repairing Stucco Cracks in Your Walls?

It is quite common to have stucco cracks. Anyone that owns stucco walls will usually tell you that have cracks in their stucco walls appear to be normal for them. Once you have stucco, you should be able to know how the cracks form and when is the best time to have them repaired. Check out the guide below what causes them, when you need stucco repair, and how to repair them: 

Different kinds of stucco cracks 

There are many kinds of cracks that usually take place in stucco walls. Basically, they happen because of various factors considered and the following will let you know how you can fix stucco cracks. Below are some of the things that you should pay attention to for you to determine the kinds of cracks you have in your stucco walls: 

Foam trim cracks 

Sometimes, the used foam trim on stucco develops some cracks. Once you can observe cracking here, it means that a fiberglass mesh tape was not utilized when they installed the foam trim. Shrinkage and expansion will then result in cracking eventually.  

Hairline cracks 

Hairline cracks are usually extremely thin with about more or less 1/16 of an inch. These types of cracks are the most typical forms of cracks that you will observe. The basically occur due to many various factors. Hairline cracks are most common in new houses while the plaster moves and settles during construction. Sometimes, construction work, shifting foundations, and drying timber will all result in hairline cracks to happen. 

Spider Cracking 

Spider cracks in your stucco is similar to spider webs in appearance, hence the name. Once you have observed this in your stucco, it is an indication that the base coat was not enabled to properly cure. This could be due to the reason that the temperature was not right when it was applied, it dried too fast or there was too much water in the mix. 

Pattern Cracking 

You might observe cracks that entail a pattern on your walls. It typically displays similar to a grid of vertical and horizontal lines on your stucco. Pattern cracking can occur since there are issues with the manner the lath was set up. Perhaps it wasn’t nailed on properly, which will result in more cracks eventually. 

Diagonal Cracking 

Diagonal cracks are naturally diagonal in shape, hence the name. Usually, they are seen around windows and doors. These occur because of the seismic changes in the foundation, which causes them to shift. Once these cracks appear wider compared to other cracks you have on your stucco wall, it would be best to pay attention to this type of crack first. 

When should you have your stucco cracks repaired? 

If you can observe any cracking in your stucco walls, the perfect time to repair them would simply be as soon as possible. Even if you only observed a tiny crack, it would be a wise idea to take action about it right away. 

Clean Your Stampede Concrete Like A Pro

You probably know already that there are numerous kinds of stamped concrete, which can make your home appear great and more valuable. After all, concrete companies can help you install a stamped concrete patio, pour a concrete driveway, or have your concrete garage floor stained to impress everybody who will visit your home. However, you probably don’t know how to maintain and clean your stamped concretes. In this article, we will discuss different methods of concrete cleaning: 

Sweeping 

Sweeping could actually help your stamped concrete to be in tip-top shape. You should know that dead leaves, which have stayed for too long, could possibly stain your stamped concrete since they organically break down. This causes them to develop chemical reactions that stain your concrete. Such stains can be permanent, which is why it would be better if you consider to clear off your stamped concrete patio by sweeping it. If you can notice any stains on your concrete, contact your local concrete contractors right away. 

Pressure washing 

Power washing or pressure washing is a process that utilizes a machine of compressed water that helps remove dirt that developed on a surface. Power washers could be electric powered or gasoline powered and could be rented from a general home improvement store. While you rent a power washer, make sure to buy a detergent intended particularly for concrete.  

Sealing 

Your stamped concrete driveway or patio would definitely display some indications of cracking after being outside for a long time or after an extreme winter. You will need to detect these cracks as sooner as you can since the cracks will begin to get even worse if you neglect it and not treat it as soon as possible. This is because water could get inside the cracks. As they get trapped, they freeze and expands and this could make the cracks even larger. 

If you experience this, you can actually handle this issue yourself and seal it. When days are warm, most of the stamped concrete can be sealed using a commercial concrete sealer. You should never do it once raining. However, it is much suggested and essential to reaching out to an expert in terms of concrete maintenance to guarantee a quality job.  

Contact Concrete Peoria Today 

Concrete Peoria proudly provides concrete services, such as a stamped concrete patio, concrete driveway, concrete finishing, and concrete repairs in Peoria at a budget-friendly price. Our skilled and certified contractors will make sure that they will meet your expectations and standards when it comes to concrete repair and installation. We have been in the business for several years, which just proves that we are experienced and skilled to offer services that will suffice your long-term goals. Visit our website to avail of our concrete services and read some informative content regularly about our offered services. Do not forget to subscribe to our email for you to get the latest update about the best products we’ve got for you to enjoy. 

Choosing the Right Dumpster Size

Everybody knows that you’ll have a lot of waste to handle if you have a major demolition or renovation project. Luckily, people nowadays can rent a dumpster to manage waste. However, for those who don’t know, there are various dumpster sizes that you have to choose from. So, how do you know you have chosen the right size for your dumpster rental ? Well, we are here to help you. 

Here are a couple of things that you have to consider to choose the ideal dumpster size for your project: 

Different Sizes of the Dumpster 

Rental companies typically measure dumpster in yards. A dumpster can accommodate a single cubic yard of material for every yard in the size. 

  • 40 Yards – This is probably the biggest size of them all. You’ll only have to rent this dumpster if the 30-yard dumpster is not enough. Usually, these dumpsters are for major demolition projects. 
  • 30 Yards – If you think that a 40-yard is simply too big, then this is your ideal option. They’re best for major demolition projects.  
  • 20 Yards – A 20-yard dumpster is usually used for major residential projects. This includes floor removals or roofing replacements. 
  • 15 Yards – This is probably the most commonly used size of dumpster. You will typically see this in apartment properties. 
  • 10 Yards – A 10-yard dumpster is usually used for minor projects, such as a de-cluttering a room. 
  • 5 Yards – A 5-yard dumpster is usually used for small projects such as bathroom renovation or lawn projects. 

Consider the Materials 

Before you choose the right size of the dumpster, you first have to think about the materials that you are going to place inside it. A couple of things are easy to manage and break down. This includes shrubbery and tree branches. However, there are also materials that are heavy and hard. If you want to ensure that the size of the dumpster properly accommodate the things you’ll be throwing, you will have to consider this a lot. Keep in mind that you have to fit the bigger items in the dumpster, especially if you do not have the tools to deconstruct them. 

Furthermore, you have to think about what materials can be serviced by the rental company. Do you have to sort the materials before dumping? Are there any materials that are hard to manage, such as liquids? Are you throwing a couple of hazardous items? If you plan ahead, you can easily choose the dumpster that properly fits your needs. Aside from the size, you also have to consider the purpose. You should also consider recycling as well. You can save a lot of space if you rent another dumpster for recycling. However, you will have to be cautious in sorting the items. You have to sort them before you place them in the dumpster. This will help prevent you from digging through the dumpster later.  

Fortunately, there are a lot of dumpster rental companies out there that can help you with your project. Make sure you hire a reliable and professional company.  

Things You Should Know About Knockdown Drywall Finish

The knockdown drywall texture has persisted to be well-used by homeowners due to its impressive practicality and appearance. The appearance is obtained by rolling, troweling, or spraying drywall joint compound onto ceilings or walls to achieve peaks that will look like a stalactite, then flattening the peaks using a knockdown knife. As a result, the naturalistic and mottled texture enhances the dimensional visual impact as it hides any imperfections on the surface as well. In addition, the treatment aids to mute sounds. Aside from that, what makes this type of finish more appealing is that those DIY enthusiast who knows fundamental drywall skills with affordable materials and tools can achieve this look easily. Keep on reading this article as we discuss to you an overview of the knockdown drywall finish.  

What are the types of knockdown texture? 

Knockdown texture comes in three different major types—mud trowel, stomp, and splatter. Each of them has their own look and needs distinct techniques and tools.  

Mud Trowel 

Mud trowel is also known as skip trowel. This kind of technique gives a more subtle and flatter look than stomp or splatter. It can be achieved by using drywall mud with a curved-blade drywall trowel that’s 18-inch or wider. Then, the mudded area will be skimmed once again using the cleaned trowel. What causes the mud to exactly skip the ceiling or wall is the curved trowel. This leaves a thin texture of quarter-sized and round globules on 50% of the surface. It would take a lot of patience if you want to do hand troweling, which makes this technique a lot more time-consuming. 

Stomp 

Among the three types, stomp is arguably had the most prominently textured look. Also, compared to mud trowel or splatter, stomp has a higher elevation off the surface. It is achieved by thinning read-to-mix or pre-mixed drywall mud and water and then using it to a ceiling or wall with a paint roller. Then, a stiff-bristled brush will be stomped into the mud. Lastly, the mud will be flattened using a basic knockdown knife that leaves a finger-like texture on 60% or more of the surface.  

Splatter: 

The most prevalent knockdown texture would be the splatter.  

It has the classic appearance of the lace stucco of Spain that was inspired by lace veils. It is created first by spraying the surface with the help of a drywall hopper gun packed with either joint compound powder or wet drywall mud mixed with water.  Then, the developed peaks are flattened with a knockdown knife to create a low-profile raised texture that encompasses 40% of the surface. The application can surely be a little messy, specifically upon spraying a ceiling. Also, since a drywall hopper gun is needed, this method needs more primary setup time compared to mud trowel and stop. However, as soon as you have mastered it, the application will be less tiring, uniform, and quicker. 

For more tips about drywall services, particularly Reno drywall repair, visit our website regularly.